List of Project Topics on MATLAB for Mechanical Engineering Students with Free PDF Downloads. This article also provides Mech based Matlab Mini Projects for Beginners with Full Source Code.
Mechanical based MATLAB Project Ideas:
- Strategies for Co-operated Wood Chip Fired and Municipal Waste Fired Combined Heat and Power Plants
The Brista 1 plant is a wood chip-fired combined heat and power (CHP) plant located near Märsta, northwest of Stockholm, Sweden. The primary purpose of the plant is to supply heat to the northwest… - Transmission Alternatives for Grid Connection of Large Offshore Wind Farms at Large Distance
With the great possibility of offshore wind power that can be installed in the world seas, offshore wind power is starting to get and important source of energy. The growing sizes of wind turbines and a growing distance to land, makes the choice… - Design and Simulation Automobile Active Suspension System
The purpose of this project is to design and simulate a semi-active suspension system for a quarter car model by controlling two input, spring stiffness, ks, and damper rate, bs. The performance of this system will be compared with the passive… - Thermal Simulation of Hybrid Drive System
Safety, performance and driving comforts are given high importance while developing modern day cars. All-Wheel Drive vehicles are exactly designed to fulfill such requirements. In modern times, human concern towards depleting fossil fuels… - Two-wheeled Self-balancing Robot: Design and Control Based on the Concept of an Inverted Pendulum
In the last decade, the open source community has expanded to make it possible for people to build complex products at home. In this project a two-wheeled self-balancing robot has been designed. These types of robots… - Design of a PV System With Variations of Hybrid System at Addis Ababa Institute of Technology
The aim of hybridizing renewable energy sources is that the main load shall be covered by the available solar energy source and other sources shall function as a complement when there is a deficiency in the main source… - Mild Hybrid System in Combination with Waste Heat Recovery for Commercial Vehicles
Performance of two different waste heat recovery systems (one based on Rankine cycle and the other one using thermoelectricity) combined with non-hybrid, mild-hybrid and full hybrid systems are investigated… - Sizing and Balance Module Development for Aircraft Conceptual Design
This thesis work was done in order to improve the capabilities in a preliminary aircraft analysis program, DIBA, at Saab Aerosystems. The areas that this was done are in the sizing and balance. One sizing tool was developed… - Heat Exchanger Design for Solar Gas-Turbine Power Plant
The aim of this project is to select appropriate heat exchangers out of available gas-gas heat exchangers for used in a proposed power plant. The heat exchangers are to be used in the power plant for the purposes of waste heat recovery… - Analysis of the Z-wing configuration
This project will analyze the Z-wing configuration. The Z-wing configuration is basically an airplane that has one of the wings placed at the forward section of the fuselage and the other wing placed on the other side far aft at the fuselage… - Modular Hybridization of Solar Thermal Power Plants for Developing Nations
The current energy scenario in the developing nations with abundant sun resource (e.g. southern Mediterranean countries of Europe, Middle-East & North Africa) relies mainly on fossil fuels to supply the increasing energy demand… - Comparative studies and analyses of working fluids for Organic Rankine Cycles – ORC
This work investigates the optimal working fluids for Organic Rankine Cycles ORC with focus on thermo-physical, environmental and safety aspects. The choice of the working fluid is of key importance for the cycle efficiency… - Modelling and Simulation of Temperature Variations of Bearings in a Hydropower Generation Unit
Hydropower contributes around 20% to the world electricity supply and is considered as the most important, clean, emissions free and economical renewable energy source. Total installed capacity of Hydropower generation is approximately 777GW… - Simulation of Rail Wear on the Swedish Light Rail Line Tvärbanan
Rail wear can result in extensive costs for the track owner if it is not predicted and prevented in an efficient way. To limit these costs, one measure is to predict rail wear through wear simulations. The purpose with this work is to perform… - Camera Spectral Sensitivity Characterization using a Blackbody Source
With digital cameras emerging as more effective tools for scientific research, there is increasing need for accurate and inexpensive ways to calibrate them. In particular, to date there has been no simple method to measure camera sensitivity… - Polygeneration system based on low temperature solid oxide fuel cell/micro gas turbine hybrid system
Polygeneration systems attract attention recently because of their high efficiency and low emission compare to the conventional power generation technology. Three different polygeneration systems based… - A finite element method for calculating load distributions in bolted joint assemblies
Bolted joints are often the most critical parts with respect to fatigue life of structures. Therefore, it is important to analyze these components and the forces they are subjected to. A one-dimensional nite element model of a bolted joint…
More >> MATLAB based projects for Mechanical Engineering Students
For More Mechanical Mini Projects and Final Year Projects with Downloads
More @ More MATLAB projects for Mech Students